Star Micronics TSP143IIU ECO Manuel

Hardware Manual Model: TSP143IIU

– 7 –3-3. Connecting to a Peripheral UnitYou can connect a peripheral unit to the printer using a modular plug. e following describes how to install

– 8 –3-4. Turning Power On and Power OImportant:is printer is not equipped with a power switch.1) e following four conditions are necessary to tur

– 9 –CAUTION• Depending on the computer that is connected to the printer, the printer may not enter the system o mode even if the computer is turned

– 10 –Cover open lever1) Push the cover open lever, and open the printer cover.2) While observing the direction of the roll, set the paper roll into

– 11 –3-5-2. Using 57.5 mm Width Paper RollWhen using a paper roll with 57.5 mm width, install the supplied paper guide on the printer.To change the e

– 12 –Caution Symbolese labels are located near the thermal print head.Because the thermal print head is hot immediately after printing, do not touch

– 13 –CAUTION1) Do not operate the cover open lever while pressing on the printer cover with your hand. 2) Do not push the cover open lever and open

– 14 –4. Attaching the Accessoriese following accessories are necessary when mounting the printer to a wall.• Upper guide and two anged screws• Hold

– 15 –4-2. Attaching the Holder Plate• e holder plate is attached to the printer using the included screws and is hooked onto screws that are insta

– 16 –(2) Position the printer over the screws, etc., on the wall and then slide it downward to set it in place. Aer setting the printer in pl

Federal Communications CommissionRadio Frequency InterferenceStatementis device complies with Part 15 of the FCC Rules. Operation is subject to the f

– 17 –4-3. Attaching the Rubber Feet(1) Attach the four rubber feet in the posi-tions shown in the gure. Ensure that any soiling has b

– 18 –5. Thermal Roll Paper SpecicationWhen consumable parts have run out, use those specied below.5-1. Compliant Paper Roll Specicationsickness

– 19 –6. Control Panel and Other Functions6-1. Control Panel1 POWER lamp (Green LED)3 FEED button2 ERROR lamp (Red LED)6-2. Lamp Indicator1) Printe

– 20 –2) Automatically recoverable errorsError Description POWER Lamp ERROR Lamp Recovery ConditionsCover open error On On Automatically recovered a

– 21 –6-3. Self-PrintingTest Printing1) Make sure that the computer is turned on.2) Make sure that the printer’s power cord is plugged into an AC out

– 22 –7. Preventing and Clearing Paper Jams7-1. Preventing Paper Jamse paper should not be touched during ejection and before it is cut.Pressing or

– 23 –Thermal headCaution Symbolese labels are located near the thermal print head.Because the thermal print head is hot immediately after printing,

– 24 –7-3. Releasing a Locked Cutter If the auto cutter locks up, disconnect the USB cable, and unplug the power cord to turn the printer o. en rec

– 25 –(4) Insert a Philips screwdriver into the manual operation hole on the side of the cutter, and turn it in the direction of the arrow shown on t

– 26 –Thermal headRubber roller8. Periodical CleaningPrinted characters may become partially unclear due to accumulated paper dust and dirt. To preven

Please access the following URLhttp://www.starmicronics.com/support/for the latest revision of the manual.TABLE OF CONTENTS1. Unpacking and Installati

http://www.starmicronics.com/support/

– 1 –1. Unpacking and Installation1-1. UnpackingAer unpacking the unit, check that all the necessary accessories are included in the package.Fig. 1-

– 2 –1-2. Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about where you plan

– 3 –1-3. NomenclatureDKO lCover open lever Push this lever in the direction of the arrow to open the printer cover.Control panelFeatures LED indi

– 4 –2. Product Features2-1. Product Features• is printer is not equipped with a power switch. e printer turns on when the computer, which the prin

– 5 –3. Setup3-1. Connecting the Power Cord(1) Check the label on the back or bottom of the printer to make sure its voltage matches that of the AC

– 6 –3-2. Connecting the USB Cable to the PrinterPass the cable through the cable support as shown. en, connect the USB interface cable to the print